S32750 Pipe Internal Discoloration: How to Investigate Fabrication and Cleaning History

Nov 18, 2026

Leave a message

Cindy Zhang
Cindy Zhang
Technical Consultant at Jinie Technology, providing expert advice on material selection and processing solutions. Specialized in duplex steel, Hastelloy, and Inconel applications for industrial projects.
Key Facts About S32750 Pipe

 

Aspect

What it means for the investigation

Material in scope

UNS S32750 (EN 1.4410, X2CrNiMoN25-7-4), also supplied as F53 forgings and flanges, in pipe to ASTM A790 (seamless and welded) and ASTM A928 (electric fusion welded).

What discoloration actually is

An oxide, stain or deposit on or in the bore surface. It is not an alloy defect and it does not by itself mean the pipe was made to the wrong chemistry.

The consequence that matters

S32750 resists corrosion through a chromium-rich passive film only a few nanometres thick. Heat tint leaves a chromium-depleted layer beneath the oxide that can pit before the surrounding metal does.

Why the bore is the hard case

It is the surface that is hardest to purge, hardest to drain, hardest to rinse and hardest to inspect. The same bore usually has the least documented history.

First questions to answer

Is the discoloration inside only or inside and outside? Is it a band at a weld, a general film, or discrete spots? Does it wipe off? Does it survive a solvent wipe?

The fastest field screen

A white-cloth wipe followed by the ASTM A380 ferroxyl test. Blue on the filter paper means free iron is present; a color that wipes away means a deposit rather than bonded oxide.

Reconstruction method

Read color, pattern and location together, then confirm with a chemical test and a laboratory corrosion test. Any single observation is ambiguous.

Critical limit

A good ASTM A923 report and a good ASTM G48 result describe the material. They say nothing about the condition of the bore.

Document that closes the argument

The mill certificate plus the pickling and passivation process record, the back-purge oxygen log for any welding, and a borescope record of the bore.

When to stop investigating

When pitting is confirmed, when the wall thickness no longer meets the minimum, or when the bore has been attacked by a chloride that the grade cannot carry.

 

S32750 Pipe Internal Discoloration

 

Summary: Internal discoloration in a super duplex pipe bore is a record, not just a blemish. The color, the pattern and the position of the discoloration each point back to a specific step in the pipe's life: how it was solution annealed, whether it was pickled, whether it was welded and how well it was purged, how it was handled, and how it was stored. This guide sets out a repeatable method for reading that record on UNS S32750 pipe supplied to ASTM A790 and ASTM A928, and for deciding what can be cleaned, what must be repaired, and what has to be rejected.

 

What does internal discoloration on S32750 pipe actually tell you?

 

It tells you the history of the pipe. A stain inside a bore did not appear during service by accident; it was made by something that touched the metal. That thing was usually one of five operations: hot forming, solution annealing, welding, acid cleaning, or handling and storage.

 

This matters more on super duplex than on ordinary stainless steel, and the reason is the alloy's own corrosion mechanism. S32750 resists chloride attack because it carries 24 to 26 percent chromium, 3 to 5 percent molybdenum and 0.24 to 0.32 percent nitrogen, giving a PREN above 40. All of that protection sits in a chromium-rich passive film only a few nanometres thick. Damage that a 316L bore would shrug off can consume a meaningful share of the super duplex corrosion margin, because that margin was never large to begin with.

 

So the practical question is not 'is this stain ugly'. It is 'which process step made this stain, and did that step also remove chromium from the surface'. The second part of the question is what decides whether the pipe can go back into service.

 

Key point: A discolored bore is not automatically a rejected bore. Mill scale, weld heat tint and free iron are all removable, and all three are recoverable with a correct cleaning sequence. What is not recoverable is pitting, wall loss, and the chromium-depleted layer left behind by heat tint that was never pickled off.

 

What is the difference between a mill condition, a fabrication condition and a service condition?

 

This is the single most useful distinction in an investigation, because each category has a different owner and a different remedy. A mill condition was created at the producer's works before the pipe was packed. A fabrication condition was created during forming, welding or spool assembly. A service condition was created after the pipe was installed and filled.

 

Reading the pipe's own paperwork usually settles the category faster than any test. The mill certificate states the delivery condition. If the delivery condition is solution annealed and pickled, and the pipe arrived with a discolored bore, then the discoloration was introduced after the mill. That single line of reasoning redirects the entire investigation from the producer to the fabricator or the site.

 

Table 1. Three categories of bore condition, and where each one originates

 

Category

Where it was created

Typical signature inside the bore

Who owns the remedy

Mill condition

Producer's works: hot forming, solution annealing, pickling, capping

Uniform mill scale in a seamless pipe; a matte pickled finish with no local features; possibly residual acid film if the rinse was short

Producer, on the strength of the mill certificate and the delivery condition

Fabrication condition

Shop or spool site: bending, welding, back purging, post-weld cleaning, grinding, marking

A colored band at a weld root; a band tracking a bend or a forming tool; specks along a grinding path; a strip where an ID grinder ran

Fabricator, against the approved welding and surface treatment procedure

Service condition

Installed system: process fluid, chlorides, heat, dead legs, insulation, cooling water

Tea staining on a smooth bore; pits and rust bleed at crevices; orange to black film in water or steam service; corrosion under insulation at seams

Owner and process engineers, against the service environment

 

The middle row is where most super duplex disputes land. A mill-pickled pipe can acquire fresh weld tint during spool assembly, so the original mill finish says nothing about the final fabricated condition. This is the same point made in the JN Alloy guidance on super duplex pickling after fabrication.

 

How do you read the color, and what are the limits of reading it?

 

Color is the fastest signal you have, and it is the one most often over-trusted. Read it as a first hypothesis generator, never as a conclusion. The color tells you what class of process caused the mark; the pattern tells you where; the wipe test tells you whether it is bonded; and only a chemical or laboratory test tells you what it is made of.

 

How do you read the color and what are the limits of reading it

 

Two pieces of discipline make this reliable. First, always record the color against a physical reference rather than against a verbal description, because 'dark blue' covers a wide range of appearance under different lighting. Second, never diagnose from a color alone, because the same color can be produced by different mechanisms. A grey film inside a bore, for example, can be unremoved mill scale, or it can be the residue of a failed pickling bath left to dry.

 

Table 2. What each discoloration signature usually means, and how it is confirmed

 

What you see

Most likely origin

How the pattern is distributed

Confirmation test

Straw to light gold, narrow band at a weld

Minimal oxidation during welding; a well-purged root

Follows the weld toe and root symmetrically

AWS D18.2 color comparison against an approved reference

Blue, purple, grey or black band at a weld

Root oxidation from inadequate back purging; chromium-depleted layer under the oxide

Follows the weld; worse where purging was difficult, such as the invert

AWS D18.2 color chart plus a corrosion test on a specimen from the band

Uniform matte grey over the whole bore

Correct and complete pickling, or unremoved mill scale

Even and circumferential; no local features

Ferroxyl test, then a borescope comparison against an approved reference

Orange to rust-brown speckles

Free iron transferred from carbon steel tools, dust, slings or rollers

Discrete points; often along handling or grinding paths

ASTM A380 ferroxyl test; blue at the contamination sites

Light to medium brown film that wipes away

Tea staining, a surface deposit from a mildly aggressive wet environment

Broad and diffuse; often worse in crevices and at the invert

Wipe test with white cloth; ferroxyl negative; no pitting under magnification

Orange to black film in water or steam service

Rouge, an iron-oxide based protective coating used on chemical equipment

Broad film, graded from orange to black

Borescope grading against the rouge classification, then derouge and repassivate

Brown film that does not wipe away

Pickling or passivation residue, or chloride salt left by a poor final rinse

Broad and even; often concentrated at the invert where solution collects

Rinse-water chloride and conductivity records; surface analysis if available

Discrete pits, rust bleed from pinpoint sources

Pitting or crevice corrosion initiated by free iron, chlorides or crevice geometry

Individual points; frequently at welds, gasket seats or the invert

Magnification, dye penetrant, then a laboratory pitting test

 

The pattern distribution column is doing most of the diagnostic work in that table. A band that follows a weld is a welding problem. Specks that follow a tool path are a handling problem. A diffuse film over the whole bore is a cleaning problem. Individual pits are a corrosion problem. Once you separate those four families, most cases resolve without a single laboratory test.

 

Which fabrication and cleaning history does each signature point back to?

 

This is the reconstruction step, and it is where the article earns its keep. Each stage of the pipe's life leaves a mark that is different from every other stage's mark. Read the mark backwards and you recover the sequence of events.

 

Table 3. Reading the bore backwards: process step, the mark it leaves, and the record that should confirm it

 

Process step in the pipe's life

Mark left inside the bore

What it tells you about the history

Record to request

Hot forming, rolling or forging

Adherent mill scale, thicker in patches; often dark blue to grey

The pipe was formed hot and the scale was not fully removed afterwards

Mill certificate delivery condition; forming route on the certificate

Solution annealing

Evenly distributed oxide over the whole bore, with no local features

The anneal was performed and the quench was adequate enough to fix the phase balance; the scale is what remains of it

Annealing temperature and quench record; ferrite content result

Pickling at the mill

Uniform matte surface, no scale; possibly a faint film if the rinse was short

Scale was removed; whether the mill achieved a clean passive surface is a separate question

Pickling procedure reference; final rinse chloride result

Cold forming or bending

Discoloration confined to the bent length, often on the outside of the bend with a matching band inside

Heat input during forming was high enough to tint the surface

Forming procedure and minimum bend radius; post-form solution anneal record

Welding and back purging

Colored band at the root, strongest at the invert

Residual oxygen in the purge gas was above the level the alloy needs

Welding procedure qualification; back-purge oxygen log; shielding gas type

Post-weld cleaning

A clean band either side of a still-tinted region, or a patchy irregular film

Cleaning was partial, or was done with a chemistry that suits austenitic grades rather than super duplex

Post-weld cleaning procedure and the bath chemistry actually used

Grinding and mechanical finishing

Dull streaks or bright patches along the tool path, often with speckling

Carbon steel tooling or contaminated abrasive was used, or iron-free tooling was not used at all

Tooling control record; whether dedicated stainless tools were issued

Handling, lifting and transport

Discrete rust-colored specks at sling points, contact points and the invert

Free iron was transferred to the surface; the base metal did not corrode

Handling procedure; whether dedicated slings and wooden supports were used

Storage

A band at one end of the bore, or discoloration concentrated where water collected

Caps were missing or ineffective, and chloride-laden moisture sat against the surface

Packaging and capping method; warehouse conditions; time in storage

Commissioning and service

Discoloration that developed after the pipe was filled and running

The process environment, not the fabricator, is the cause

Commissioning flush records; service chemistry and temperature history

 

One row in that table deserves emphasis because it is the most common and the most expensive to discover late. The storage row. A bore that is clean at delivery and discolored at installation has a storage problem, and no amount of pickling will fix the fact that the pipe sat with water and chloride in it. It has to be repaired on its merits, and the storage and capping method has to be corrected so the next delivery does not repeat it.

 

How does S32750 compare with 316L and standard duplex 2205 in this respect?

 

Super duplex is more resistant to pitting than the alternatives, which sounds like an argument for being relaxed. It is the opposite, and the reason is worth stating precisely for buyers who are deciding how much effort to spend on a discolored bore.

 

The higher the PREN, the wider the gap between a healthy surface and a damaged one. When a 316L bore is pitted, it has usually lost most of its local corrosion margin, because 316L does not have much to lose. When a super duplex bore is pitted, it has consumed part of a much larger margin, and the remaining life question becomes a genuinely different calculation. In practice, the correct engineering response to a damaged super duplex surface is to treat it as a defect requiring an engineering disposition, not as a cosmetic cleaning job.

 

Table 4. Comparing the common stainless grades against internal discoloration risk in a pipe bore

 

Property

TP316L

Duplex 2205 (S32205)

Super Duplex 2507 (S32750)

Why it matters for the bore

PREN (typical)

About 24 to 26

About 33 to 35

About 41 to 43

Sets how much pitting margin exists once the surface is damaged

Nickel content

10 to 14 percent

4.5 to 6.5 percent

6.0 to 8.0 percent

Low nickel is why duplex needs nitrogen to hold austenite in balance

Nitrogen content

Not deliberately added

0.08 to 0.20 percent

0.24 to 0.32 percent

Nitrogen stabilises austenite and drives the pitting resistance; it is also what is lost at a poorly purged root

Effect of a chromium-depleted layer

Significant loss of local pitting resistance

Significant loss, and the depleted layer can be attacked by chlorides

The same mechanism, applied to an alloy with more chromium to deplete, so the relative loss is larger

Why heat tint must be pickled off rather than passivated over

Root behavior in welding

Tolerance for some nitrogen pickup; wide root window

Nitrogen loss at the root risks a ferrite-rich root and Cr2N precipitation

More sensitive still, because the austenite balance depends on nitrogen and on the fillet match

Why back-purge oxygen targets are tighter for super duplex

Pickling behavior

Fast; standard austenitic acid schedules work

Slower than austenitic; the schedule must be qualified for the grade

Slower again, because molybdenum and nitrogen resist the acid bath

Why a pickling recipe borrowed from a 316L job can leave scale on a 2507 bore

Recommended back-purge oxygen target

50 to 100 ppm

25 to 50 ppm

25 to 50 ppm

Set by the need to hold nitrogen at the root, not by appearance alone

Consequence of leaving free iron on the bore

Rust spotting, then pitting

Rust spotting, then pitting in the affected zone

Rust spotting over a smaller but more consequential area

Why the ferroxyl test matters before any chloride service

 

The last row of that table carries the practical lesson. The free iron test is not a formality on a super duplex bore. A small amount of surface iron that would produce a cosmetic speck on 316L is a legitimate pitting initiation site on a 2507 line intended for seawater or sour service.

 

What does weld root oxidation tell you about the fabrication history?

 

It tells you the back purge was not controlled, and it is the clearest single indicator of how the pipe was welded. Root oxidation on the inside of a pipe is not caused by the service environment. It is caused at the moment the arc was struck, when air was still inside the joint.

 

What does weld root oxidation tell you about the fabrication history

 

This is where super duplex is genuinely unforgiving. The AWS D18.2 guide ties the root-side color to the oxygen content of the purging gas, and shops that wait for the purge to fall below about 100 ppm are meeting the standard austenitic requirement. That target is not tight enough for super duplex, where the residual oxygen target of 25 to 50 ppm protects the nitrogen balance at the root. The JN Alloy guide to back purging techniques for stainless steel pipe welding sets out the volume-exchange planning behind those numbers and why an oxygen analyser reading at the vent, not a calculated purge time, is the release criterion.

 

Table 5. Purge gas oxygen targets and the resulting root color, by alloy family

 

Alloy family

Target residual oxygen

Typical root color

What a failure looks like

300-series austenitic (304, 316, 321)

50 to 100 ppm

Light straw to no color

Faint blue or grey band at the root

Duplex and super duplex (2205, 2507)

25 to 50 ppm

Light straw or better

Blue, purple, grey or black band, worst in the invert

Nickel alloys (625, C276, 825)

25 to 30 ppm

Light straw or better

Any visible root color; the surface is very sensitive to oxidation

High-purity pharmaceutical and semiconductor

Below 10 ppm

No visible color; mirror finish

Any visible color at all

 

Two practical points follow from that table. The first is that a shop with a good austenitic weld history may still fail on super duplex, because the purge discipline is genuinely different. The second is that nitrogen must never be used to back-purge duplex or super duplex, because the weld pool absorbs it and the austenite balance shifts with it. Argon is the only inert gas appropriate here.

 

What does the pickling history reveal about the pipe, and why is it risky?

 

A correctly pickled super duplex bore is matte and even, with no color and no scale. That is the target, and it is a specific physical condition rather than an appearance preference. It means the oxide scale has been dissolved and the chromium-depleted layer beneath it has been removed with it, leaving clean metal ready to re-passivate.

 

The risk is that pickling schedules travel badly between grades. A bath and cycle that works on 304 or 316L can leave a film of scale and a chromium-depleted layer on a 2507 bore, because super duplex grades with high molybdenum and nitrogen pickle more slowly. The result looks like a partially pickled surface, which is worse than a surface that was never pickled, because it invites an inspector to accept a condition that is only part way there.

 

Two failure modes are worth separating. Under-pickling leaves scale and a chromium-depleted layer. Over-pickling attacks the base metal, and it produces etching, pitting, frosting, an uneven appearance and dimensional loss. The first is a corrosion risk. The second is a mechanical one, because the wall thickness has been reduced and the tolerance is now out of position. The JN Alloy article on acid cleaning failures covers how concentration, temperature and time interact and why all three have to be in range at the same time.

 

Table 6. Pickling and passivation: what each treatment removes, and what it cannot repair

 

Treatment

What it removes

What it cannot do

Consequence on a super duplex bore

Degreasing and pre-cleaning

Oil, grease, drawing compound, general shop dirt

Does not remove oxide scale or heat tint

Mandatory before any acid step; oil blocks the bath locally and creates untreated patches

Pickling

Oxide scale, heat tint, and the chromium-depleted layer beneath them

Does not restore metal lost to pitting; cannot correct a wrong heat treatment or a bad weld

The only treatment that removes a heat tint damaged layer; must be qualified for the grade

Chemical passivation (nitric)

Free iron and other exogenous contamination; supports passive film re-formation

Does not remove heavy scale or heat tint; changes no dimension

Correctly sequenced after pickling; a passivation treatment over heat tint is a defective delivered item

Chemical passivation (citric)

Free iron, with less risk of attacking thin-wall material

Poor at removing heat tint or heavily embedded iron

A useful alternative where over-pickling risk matters; not a substitute for pickling

Electropolishing

A uniform metal layer, including embedded contamination, burrs and heat tint

Requires a submerged setup; does not correct a metallurgical condition

Note that ASTM B912 as written covers the 200, 300 and 400 series and precipitation-hardened alloys, so applicability to super duplex should be confirmed against the contract edition

Mechanical cleaning

Loose oxide, tool marks and surface defects

Can smear metal, embed iron and leave a mechanically disturbed surface that passivates poorly

Use stainless-dedicated tools and follow with passivation

 

Key point: The single most common delivery failure on fabricated stainless assemblies is a passivation treatment applied over heat tint. It looks like a completed surface treatment on the paperwork and it leaves the chromium-depleted layer exactly where it was. Specify the sequence, not the label.

 

Which test proves which cause, and what does each test not prove?

 

No single test answers the question, and the most common investigation error is treating a negative result from one test as a clean bill of health. Each test has a specific detection limit and a specific blind spot. The table below states what each one proves and, more importantly, what it leaves open.

 

Table 7. Investigation tests: what each one proves and what it does not

 

Test

What it proves

What it does not prove

Main limitation

Visual examination under bright, angled light

The presence, position and general character of discoloration, scale, pits, slag and surface damage

The chemical nature of the deposit; whether the base metal is sound underneath

Needs good lighting; a bore reflects light rather than diffusing it

Borescope or videoborescope

Surface condition of the bore at the locations actually reached, including pits, scratches, inclusions and weld residue

That the whole bore was seen; coverage is commonly well below 100 percent

Access, lighting and reach are the limiting factors, not the instrument

White-cloth wipe test

Whether the discoloration is a loose deposit that lifts onto the cloth

What the deposit is made of, or whether a bonded layer exists underneath

A negative result does not exclude a bonded stain; it only excludes a loose one

ASTM A380 ferroxyl test

Free iron on the surface, at trace levels

Heat tint; scale; the chemistry of a bonded film; the integrity of the base metal

Extremely sensitive, so it can give false positives from pickling residue; must be read within about 15 to 30 seconds and rinsed off immediately

ASTM A380 copper sulphate test

Presence of iron or carbon steel contamination; broader scope than ferroxyl

Trace-level free iron; it is less sensitive

Preferred on ferritic grades where ferroxyl is less reliable

Water-break test

Even wetting of the surface, which indicates a continuous and clean surface

Whether the passive film is present or the metallurgy is sound

A qualitative indicator only; it needs a clean surface to begin with

ASTM G48 Method A

Resistance to ferric chloride pitting of the sampled material

The condition of the bore away from the specimen; a surface film on a specimen that was pickled before testing

Specimen preparation dominates the result, and pickling the specimen changes the weight loss

ASTM A923 Method C

Presence of detrimental intermetallic phase in the sampled material

Surface condition; the condition of unsampled regions

Must be sampled from the most slowly cooled region, not the surface

Ferrite measurement (ASTM E562 or a calibrated magnetic instrument)

The ferrite fraction of the sampled material

The condition of the passive film, or the presence of sigma phase at a small fraction

Surface readings can understate the true content and vary with product form

PMI / handheld XRF

The alloy grade of the sampled surface

Carbon and nitrogen content; the heat treatment condition; anything below the instrument's sampling depth

Readings reflect a thin surface layer only

Dye penetrant examination

Surface-breaking defects such as cracks

Subsurface defects, or the chemistry of a discoloration

Requires a clean, uncoated surface

Rinse-water chloride and conductivity records

Whether the final rinse left chlorides or salts on the surface

Anything about the pipe before the rinse

A record is evidence of the process, not of the current surface state

 

Two rows in that table deserve a note. The ferroxyl test is the most powerful field screen and also the most over-read: because it is hypersensitive, pickling residues can produce a blue result on a surface that carries no contamination, which is why the area must be rinsed with deionised water immediately after reading. And the ASTM G48 row carries a trap worth stating plainly. Specimens are routinely pickled before testing, and pickling reduces both the measured weight loss and the scatter between results, so a good G48 number on a pickled specimen does not certify the bore the specimen came from.

 

How do you reconstruct the fabrication and cleaning history from the pipe itself?

 

You reconstruct it by combining three independent evidence sets and looking for agreement. If all three point the same way, the conclusion is defensible. If they disagree, the disagreement is the finding, and it tells you which record is wrong.

 

Evidence set one: the physical record on the metal

  • The color, pattern and position of the discoloration, recorded photographically against a physical color reference.
  • The bore condition at the ends compared with the bore condition in the middle. A gradient points to a process, not to a material.
  • Whether the discoloration follows a weld, a bend, a tool path, a sling point or the invert. Geometry is evidence.
  • Whether the surface is smooth, etched, frosted, pitted or rough. Each texture has a different cause.
  • Whether the same pattern appears on the outside of the pipe. Inside-only points to an internal process, such as pickling or purging; inside and outside points to handling, storage or the environment.

 

Evidence set two: the documentary record

  • The mill certificate: grade, heat number, delivery condition, product form, applicable standard, and the supplementary test results.
  • The pickling and passivation process record, including the bath chemistry, temperature, time, and the final rinse water result.
  • For welded pipe, the welding procedure qualification, the filler metal, the back-purge oxygen log and the shielding gas used.
  • The post-weld cleaning record, including whether a bore cleaning operation was performed and how the pipe was drained and dried.
  • The handling, lifting and storage records, including the capping method and how long the pipe waited before installation.
  • The commissioning flush records, if the discoloration appeared after installation.

 

Evidence set three: the confirming test

 

  • A visual and borescope survey with a location map.
  • A free-iron test, either ferroxyl or copper sulphate, with the locations recorded.
  • A corrosion test on a specimen taken from the discolored zone, compared against the same test on a zone believed to be clean.
  • A phase check for ferrite content and detrimental intermetallic phase, if the thermal history is in any doubt.
  • A chemical or residual analysis of the deposit, where the decision is expensive enough to justify it.

 

The most valuable comparison in that list is the third item of the third set. A specimen from the discolored zone tested against a specimen from a clean zone turns a qualitative argument into a comparative number, and it is the only evidence that reliably separates a cosmetic stain from a corrosion risk.

 

How should the investigation be run, step by step?

 

The ten steps below are the sequence JN Alloy recommends when a client raises a discoloration query on super duplex pipe. They are ordered so that the cheapest and least invasive evidence is collected first, and so that nothing is cleaned until the evidence it would destroy has been captured.

 

How to Investigate S32750 Pipe Internal Discoloration in Ten Steps

 

Secure the evidence before touching the surface. Photograph the bore with a scale in the frame, record the pipe size, wall thickness, heat number and standard, and photograph any external discoloration at the same time. Cleaning first destroys the pattern you are trying to read.

 

Confirm the grade and the product form. Use a handheld PMI instrument on the outer surface and read the mill certificate for the heat. A 2205 pipe handled as if it were 2507 is the most common reason a discoloration investigation reaches the wrong conclusion.

 

Map where the discoloration is. Mark every location: weld joints, the 6 o'clock invert, the crown, the pipe ends, and any region opposite a support. End-of-pipe concentration points to drainage; a band at a weld points to heat tint; discrete spots point to free iron.

 

Do the wipe test. Wipe with a clean white cloth and detergent, then with solvent. If the color lifts onto the cloth it is a deposit, such as tea staining or rouge. If it stays, it is bonded oxide, a stain from the substrate, or actual attack.

 

Run the ASTM A380 ferroxyl test. Mix the potassium ferricyanide solution fresh, apply it to the bore with a soaked filter paper or a swab, and read the result at 15 to 30 seconds. A blue discoloration means free iron. Rinse the area with deionised water immediately afterwards so the reagent does not itself cause a stain.

 

Compare against the AWS D18.2 color chart. If the bore shows a color band at a weld, read it against the chart. Straw to light gold indicates a well-purged root; blue, purple, grey or black indicates oxygen levels high enough to have damaged the surface.

 

Check the chloride and residue sources. Look for chlorides in rinse water, from sea air, from wash-down, from insulation and from acid cleaning. Confirm that the final rinse was demineralised and that the pipe was drained and dried. Free iron plus chloride is the combination that turns a stain into pitting.

 

Check the metallurgical condition at the same time. Verify ferrite content and check for detrimental intermetallic phase on a representative sample, especially if the pipe has been re-heated, bent hot, repaired or stress-relieved outside a qualified procedure.

 

Corroborate with a laboratory corrosion test. Where the service is chloride, seawater or sour, test a specimen from the discolored zone by ASTM G48 Method A and, where the history includes welding or a repair, ASTM A923 Method C. Compare against the same test on a known-good zone.

 

Write the finding as a decision, not an opinion. State the observation, the test that confirmed it, the process step that caused it, the effect on corrosion resistance, the corrective action and the release decision. Give the owner a disposition they can act on.

 

The sequence matters for a specific reason. Steps one to four are all read-only and all cheap. By the time you reach step five, you are making a decision that either preserves the evidence permanently or destroys it, and the difference between a confident disposition and an argument is almost always whether the first four steps were done properly.

 

What are the acceptance criteria for a repaired super duplex bore?

 

There is no universal acceptance class, and anyone who quotes one without naming the governing document is guessing. What can be stated is the structure of the criteria and the reference documents that populate it. Acceptance has to be defined for each surface zone, and the definition has to name the test, the acceptance limit and the inspection method.

 

What are the acceptance criteria for a repaired super duplex bore

 

Table 8. A surface condition schedule: what to specify, and which reference supplies the requirement

 

Acceptance dimension

What to require

Verification method

Governing reference

Treatment coverage

Identify wetted and non-wetted surfaces, weld roots, heat-affected zones, branches, repairs and the internal zone of every length

Inspection map, direct viewing or borescope access, agreed sampling rate

Project specification and ASTM A380/A380M

Oxide removal

No visible weld heat tint and no adherent scale on the designated surfaces

Visual examination under defined lighting, plus comparison with an approved reference sample where one is available

AWS D18.2 color reference; ASTM A380/A380M

Free iron

No free iron, or a defined acceptance level where a specification allows one

ASTM A380 ferroxyl or copper sulphate test at agreed locations

ASTM A380/A380M; ASTM A967/A967M

Residue and salts

No visible pickling residue, and no chloride residue from the final rinse

Rinse-water chloride and conductivity records; visual inspection of the invert

Project specification; rinse-water records

Treatment damage

No unacceptable pitting, etching, preferential attack or dimensional loss caused by the treatment itself

Visual criteria against an agreed reference, plus dimensional checks on critical features

ASTM A380/A380M; ASME B31.3

Roughness and function

Drawing requirements for flow surfaces, sealing faces, threads and any other functional feature

Roughness parameter, numerical limit, inspection locations and measurement method, stated separately from appearance

Drawing; ASME B16.25 and B16.5 where applicable

Corrosion performance

A specified pitting test, method, specimen location, preparation and acceptance limit, only where the service warrants it

ASTM G48 Method A, with specimen preparation and acceptance stated, not assumed

ASTM G48; NORSOK M-601 and M-650 where applicable

Metallurgical condition

Solution annealed with ferrite in the required range, and no detrimental intermetallic phase

Ferrite measurement and intermetallic phase testing on a representative sample from the most slowly cooled region

ASTM A923; ASTM A1084; ISO 15156-3

Documentation

Traceability from the component to its treatment and inspection records, including nonconformities, corrective action and release approval

Process record, inspection report, repair record, release approval

EN 10204 3.1 and EN 10204 3.2 where a certificate is specified

 

Two rows in that schedule are routinely omitted from real purchase orders and are the ones that cause the most trouble later. Roughness is never specified as a number, so everybody assumes a standard finish, and then nobody can say whether the delivered bore met it. Corrosion performance is mentioned as 'to ASTM G48' without a method, a specimen location, a preparation step or an acceptance limit, which means the result depends on how the laboratory chose to prepare the coupon. Write those two rows out in full.

 

What are the decision rules: clean, repair, or reject?

 

Three outcomes are available, and the decision follows from what the tests actually proved, not from how the bore looks. The rule below is the one JN Alloy applies to client queries, and it is deliberately conservative because the alternative is a failure in service.

 

Table 9. Decision table: from observation to disposition

 

What you observe

What it most likely is

First action

Disposition

Color band at a weld, no pitting, surface sound under magnification

Weld heat tint from imperfect back purging

Compare with the AWS D18.2 chart; measure the wall; confirm the base metal is sound

Repair by pickling to remove the oxide and the chromium-depleted layer, then passivate and verify

Even matte grey bore, uniform, no local features

Mill scale, or a completed pickling operation

Ferroxyl test; borescope against an approved reference

If scale remains, pickle and passivate, then verify by ferroxyl and corrosion test

Rust-colored specks near tool marks or handling points

Free iron embedded on the surface

Ferroxyl test; identify and remove the iron source; check for chloride exposure

Pickle if the contamination is heavy, otherwise passivate; re-test before release

Tea staining that wipes away, smooth surface, no crevices

A surface deposit from the environment

Clean with detergent and deionised water; confirm ferroxyl negative; check for pitting

Accept, with the drainage, ventilation and finish conditions reviewed

Pickling residue or salt film in the invert

Inadequate final rinse, or chloride residue

Rinse with deionised water, dry, and check the chloride result

Re-rinse and repassivate; verify by chloride and free-iron checks

Discrete pits, or rust bleeding from pinpoint sources

Pitting or crevice corrosion has begun

Dye penetrant, thickness measurement, laboratory pitting test

Engineering review. Wall loss means repair or replacement, not cleaning

Brown or grey film that does not wipe away, uniform over the whole bore

Unremoved mill scale, or an inactive pickling bath residue

Ferroxyl test; surface analysis; review the pickling record

Pickle and passivate with a qualified schedule, then verify

Discoloration inside only, on a pipe that arrived clean

A fabrication or storage step after delivery

Compare the delivery record with the fabrication and storage records

Repair, and correct the process that caused it so it does not repeat

Any discoloration on a line that has already been in chloride service

Corrosion until proven otherwise

Stop and assess. Thickness measurement and a corrosion test before anything else

Engineering disposition. Treat as a defect, not as a stain

 

Key point: A useful test for deciding whether you are dealing with a stain or a corrosion problem: if the discoloration can be removed and it does not come back, it was a deposit or an oxide. If it comes back, or if the surface is rough, pitted or sugary under magnification, metal was lost, and no cleaning regime will restore it.

 

How should a discolored bore be repaired?

 

The repair sequence is fixed, and the order is not negotiable. First remove the oxide, then remove the free iron, then verify. Reversing the first two steps, by passivating a surface that still carries heat tint, is the classic error and it produces a component that passes its paperwork and fails its service.

 

Step one: pickling, qualified for the grade

Pickling removes the oxide scale and, crucially, the chromium-depleted layer beneath it. For super duplex this must be a schedule qualified for the grade, because the high molybdenum and nitrogen content means an austenitic cycle can leave both scale and the depleted layer in place. Bath chemistry, temperature and time have to be controlled together, and the wall thickness has to be checked afterwards, because over-pickling removes base metal. Where a bore cannot be fully immersed, a circulated or sprayed chemistry is used, and the pipe has to be arranged so the solution actually reaches the invert.

 

Step two: rinsing, and the step everyone under-specifies

Rinse thoroughly with demineralised water, and drain the pipe completely. Residual acid or fluoride in a crevice or a weld toe causes localised attack, and residual iron salts in the same place will show up as a blue result on the next ferroxyl test even though the bore is clean. The rinse specification, not the pickling specification, is what determines whether the job passes.

 

Step three: passivation

Apply chemical passivation to ASTM A967/A967M, choosing the nitric, citric or electrochemical route that the contract specifies, to remove residual free iron and support uniform passive film formation. Passivation does not remove scale, so if the order was wrong, passivation cannot rescue it.

 

Step four: verification

Verify the result with a free-iron test at agreed locations, a visual comparison against an approved reference sample, and where the service warrants it, a corrosion test on a specimen from the treated zone. Then record what was done, what was measured and who released it. An unrepaired and undocumented bore is indistinguishable from a bore that was quietly left as it was.

 

How do you stop the bore discoloring in the first place?

 

Prevention is a documentation and handling problem far more than it is a metallurgy problem. The following controls are the ones that JN Alloy applies across its own production and handling, and they are the ones that most often prevent the investigation above from being needed at all.

 

  1. Use dedicated stainless steel tools, brushes and abrasives. Contaminated carbon steel grinding discs are the single most common source of free iron on a super duplex bore.
  2. Use dedicated slings, softeners and supports. Protect the pipe ends from direct contact with carbon steel and from impact damage during transport.
  3. Cap the pipe ends immediately after production and keep the caps on until installation. A sealed, dry bore does not discolor.
  4. Store the pipe off the ground, under cover, with the bore protected from standing water and from chloride-laden air.
  5. For welded spools, control the back purge with an oxygen analyser and record the reading. Do not judge the purge by flow time.
  6. For welded pipe, verify the internal seam surface after welding and before the bore is closed, because once the spool is assembled the access is gone.
  7. Specify the internal surface condition in the purchase order using the surface condition schedule structure, and require the process record to travel with the pipe.
  8. Flush the line before commissioning and dry it, and record the flush. A large share of apparent fabrication defects are created in the first hour of service.

 

The first item in that list is worth repeating because it is counter-intuitive for shops used to austenitic work. Carbon steel tooling on a super duplex bore is not a cosmetic problem. It is free iron, on an alloy with PREN above 40, destined in most cases for seawater or sour service. The grade is not more fragile than 316L, but it has far less margin to spend on a careless tool.

 

Why do super duplex engineers care about this more than other stainless engineers?

 

Because of where the grade is used. Super duplex S32750 is specified where the service is severe enough that a cheaper alloy would not survive: seawater systems, desalination, subsea and offshore production, sour oil and gas, chlor-alkali and pulp and paper bleaching. The JN Alloy applications review for S32750 plate sets out the typical duty in each of those sectors. In those environments, the passive film is the whole defence, and the passive film is the first thing a chromium-depleted layer or a free-iron speck destroys.

 

The second reason is the metallurgy. Super duplex achieves its strength and its corrosion resistance from a specific two-phase microstructure, roughly equal austenite and ferrite, that is created by solution annealing and then frozen by a rapid quench. The same thermal sensitivity that makes the grade unforgiving about intermetallic phase also means the bore has to be treated as a metallurgical surface rather than as a surface that can be wiped clean and left.

 

The third reason is documentary, and it is the one that decides whether an investigation succeeds. Because super duplex pipe is expensive, heavily documented and often fitted with supplementary test results under ISO 15156 for sour service, a bore condition query tends to be answered with a certificate argument. The certificate is the right document to argue from, and it is worth understanding exactly where its authority stops. It certifies the chemistry, the mechanical properties and the supplementary corrosion and phase tests. It says nothing about the condition of the bore, and the JN Alloy guide to ASTM A923 reports for duplex products makes that boundary explicit.

 

Frequently Asked Questions About S32750 Pipe

 

Q1. Is internal discoloration on S32750 pipe a sign that the wrong material was supplied?

Usually not. In most investigated cases the discoloration comes from a fabrication, cleaning or handling step after the pipe left the mill, not from the chemistry. Grade substitution is still the first thing to rule out, because it is cheap to check and expensive to discover late. Confirm the grade by PMI and read the heat number on the certificate before investigating anything else.

 

Q2. What colors can the inside of a super duplex pipe legitimately show?

A light gold or straw tint at a weld root on a well-purged joint. A uniform matte grey after a correct pickled finish. A blue, purple, grey or black band at a weld means the purge failed. Orange-brown speckling near tool marks means free iron. A uniform light brown film that wipes away is usually tea staining. The color sets a hypothesis; the test confirms it.

 

Q3. Can a discolored super duplex bore be cleaned back to acceptance?

Often yes, but only if the underlying metal was not attacked. Pickling removes oxide scale and the chromium-depleted layer beneath it. Passivation removes free iron. Neither restores metal lost to pitting. Before any cleaning, confirm with magnification and a corrosion test that the surface is sound, because cleaning a pitted bore only removes the evidence.

 

Q4. Does passivation remove heat tint?

No. Passivation removes free iron and supports re-formation of the passive film on an already clean surface. Heat tint is a thick, chromium-depleted oxide that must be removed by pickling or mechanical cleaning first. Passivating over heat tint leaves the damaged layer in place and is one of the most common causes of failed acceptance tests on fabricated stainless assemblies.

 

Q5. How long can S32750 pipe sit in storage before the bore discolors?

There is no code limit, because the damage depends on what is present rather than on time. Chloride-laden moisture, carbon steel contact, trapped process water and inadequate end protection all act on the bore. Pipe stored with open or imperfect caps in a warm humid chloride environment is the common case, and it is a packaging and handling problem rather than a material problem.

 

Q6. Why is the bore harder to keep clean than the outside of the pipe?

Four reasons compound. Back purging is less effective in a long bore. Pickling solution and rinse water are harder to flush from the invert, so residue is more likely to survive. Drying is difficult, so dampness persists. And inspection access is limited, so a problem is often found after the pipe is already in service. Treat the bore as the governing surface in any acceptance plan.

 

Q7. Does the rust-colored film inside a pipe prove carbon steel was welded to it?

No. Free iron can arrive from carbon steel grinding discs, tool marks, iron dust in the workshop, rust-stained slings, or a pipe that was rolled on carbon steel rollers. The appearance is the same in every case, which is why the ferroxyl test and a review of the handling history are both needed to establish the route.

 

Q8. Can a weld heat tint be welded out by re-annealing the pipe?

The oxide on the bore cannot. A full solution anneal with a rapid quench would restore the phase balance and remove detrimental intermetallic phases, but it requires furnace capacity for the whole component and it does not reach inside a closed bore. It also risks new distortion. Re-annealing is not a remedy for a discolored bore and is not a normal repair route.

 

Q9. What is the difference between a chromed or bright bore and a clean bore?

A bright bore shows that oxide scale was removed. It does not prove that free iron, lubricant, chloride or pickling residue are absent. The JN Alloy guide to tube ID cleanliness sets out the same distinction for small-bore tube: a bright finish and a clean surface are different properties, and only one of them is visible.

 

Q10. Does a passing ASTM A923 report clear a discolored bore?

No. ASTM A923 tests the material for detrimental intermetallic phase. A923 itself states that compliance with the chemical and mechanical requirements of the product specification does not necessarily indicate the absence of detrimental phases, and it says nothing at all about surface condition. Read the A923 report guide for what each method proves.

 

Q11. Is tea staining on the inside of a super duplex pipe a corrosion problem?

Usually not. Tea staining is a light brown surface deposit that forms on stainless in mildly aggressive conditions and it does not affect structural integrity. On a smooth, crevice-free surface it is normally a cosmetic matter. In a crevice, under insulation, or with free iron present underneath, the situation changes, so inspect the geometry before dismissing it.

 

Q12. What is the most common cleaning error on super duplex pipe?

Using an austenitic pickling schedule. Super duplex grades with high molybdenum and nitrogen pickle more slowly than standard austenitic grades, so a recipe tuned for 304 or 316L can leave scale and a chromium-depleted layer on a 2507 bore. The second most common error is treating acid time and temperature as interchangeable, which is the failure mode covered in the JN Alloy guide to acid cleaning failures.

 

Q13. Can the bore be inspected with a standard borescope?

Yes, with limits. A videoborescope is the primary tool for internal inspection of duplex pipe, and it needs strong, angled lighting because the bore reflects light rather than diffusing it. Coverage is rarely complete in long or heavily bent pipe, so a borescope record is evidence of what was seen, not evidence that nothing else is present.

 

Q14. How do you tell heat tint from free iron when both are present?

By position and by test. Heat tint follows the weld in a band and does not wipe off. Free iron follows tool paths, handling marks and slings and is confirmed by a blue ferroxyl result. The two frequently coexist at a weld that was ground with a carbon steel wheel, which is why the two tests are complementary rather than alternatives.

 

Q15. What should the mill supply with the pipe to make this investigation possible?

The mill certificate with the heat number, the pickling and passivation process record, the final rinse water chloride result, the delivery condition, the surface finish designation, and the packaging and capping method. For welded pipe, the welding procedure, the back-purge oxygen log and the longitudinal seam radiography record close the remaining gaps.

 

Q16. Is S32750 pipe more likely to discolor than 2205 or 316L?

The material is not more prone to discoloring; it is more expensive to discolor badly. S32750 carries a PREN above 40 against roughly 33 to 35 for 2205 and 24 to 26 for 316L, so the same contaminated surface has a larger margin before pitting begins. The trade is that a damaged passive film on a super duplex bore is a larger share of the total corrosion margin, which is why the repair standard should be tighter, not looser.

 

Q17. What is the accepted repair route for a heat-tinted super duplex bore?

Pickling in a nitric and hydrofluoric acid bath, followed by thorough rinsing with demineralised water, then chemical passivation, and then verification by a ferroxyl or copper sulphate free-iron test and by a surface comparison against an approved reference sample. Where the component cannot be pickled, mechanical cleaning with stainless-dedicated tools is the alternative, and it must be followed by passivation because mechanical work leaves a disturbed surface.

 

Q18. Who should write the disposition on a rejected or repaired bore?

The engineer who owns the component, not the supplier alone. A surface observation from the supplier is evidence; the release decision needs the service conditions, the applicable code and the governing project specification. For S32750 in sour service, that means the ISO 15156 conditions and the hardness limits in NACE MR0175 and the super duplex selection guide.

Send Inquiry
Come To Us
And Start Your RFQs Now.
contact us