C276 Valve Trim Replacement: How to Match Material, Hardness, and Surface Condition

Nov 20, 2026

Leave a message

Anna Chen
Anna Chen
Junior R&D Scientist at Jinie Technology, focused on developing new materials and processes for stainless steel and nickel alloys. Passionate about innovation and sustainable manufacturing solutions.

Quick Answer

 

Match C276 valve trim on three separate checks, because a part can pass one and fail the others. (1) Material: UNS N10276 in the right product form (wrought bar to ASTM B574, forging to B564, or cast grade CW2M), confirmed by certificate and PMI. (2) Hardness: the right condition (annealed, cold-worked, or hardfaced), not just the right alloy. (3) Surface: clean, scale-free, free of embedded iron, with the seat finish the valve maker's drawing requires.

 

Do not use hardness to identify the alloy. Annealed C276 is soft (typically 86 to 88 HRBW), so many seating pairs rely on a hardfaced surface and a hardness difference between mating faces. Verify the overlay, its corrosion behavior in your fluid, and the cleaning record before the part goes in the valve.

 

C276 Valve Trim Replacement

 

Valve trim is the small set of wetted parts that do the real work: the stem, the seating surfaces, the disc or plug, and related internals. In a corrosive line, the body may last for years while the trim wears out, galls, or pits. Replacing it with "C276" is not enough. Alloy, hardness, and surface condition all have to match the way the valve was designed.

 

What does it mean to "match" C276 valve trim?

 

Matching means three checks: the right alloy and product form, the right hardness condition, and the right surface condition. Each has its own evidence document.

 

API 600 describes valve trim as the internal wetted parts that touch the fluid, including the stem, the body and gate seating surfaces, and the backseat. A trim part that matches on alloy only can still gall because its hardness pairing is wrong. A part with the right alloy and hardness can still start pitting because iron from a steel tool is smeared into its surface.

 

Table 1. The three-way match for C276 trim

 

Dimension

What must match

Evidence to ask for

What goes wrong if it does not

Material

UNS N10276, right product form (B574 bar, B564 forging, CW2M cast)

EN 10204 3.1 certificate; PMI report

Wrong alloy or wrong chemistry limits

Hardness

Condition (annealed, cold-worked, hardfaced) and the hardness pairing across the seating faces

Hardness report with scale and test location; overlay report

Galling, early wear, seat leakage

Surface

Clean, scale-free, no embedded iron; finish and flatness per seat drawing

Cleaning or pickling record; iron test; seat leakage test

Pitting start, leakage, contamination

 

Sources: API 600 trim definition and trim chart (secondary reproductions); Haynes International C-276 datasheet; EETA summary.

 

Which C276 product forms and standards apply to trim?

 

Use ASTM B574 bar or B564 forgings for wrought trim, and treat cast CW2M as a separate material with its own specification. Confirm the form on the certificate; do not assume it from the part.

 

Wrought C276 is supplied solution annealed unless ordered otherwise. Haynes lists bar and billet under ASTM B574 and B472, plate under B575, forgings under B564, and fittings under B366 and B462. It also lists NACE MR0175 / ISO 15156 coverage. The API 600 trim chart shows C276 trim as a cast grade (ASTM A494 CW2M) or a forged part (B564 N10276), with ERNiCrMo-4 as the weld filler.

 

Table 2. Product forms and standards for C276 trim parts

 

Form

Standard

Typical trim use

Key point

Rod and bar

ASTM B574 / SB574 (and B472)

Stems, plugs, discs and seats machined from bar

Solution annealed: min 100 ksi tensile, 41 ksi yield, 40% elongation

Forgings

ASTM B564 / SB564

Larger seats, discs, bonnets

Named for forged C276 trim in the API trim chart

Plate and sheet

ASTM B575 / SB575

Cut or formed internals, bellows and thin parts

Haynes typical room-temperature yield about 51.6 to 52.9 ksi

Castings

ASTM A494 grade CW2M

Cast discs and bodies

Separate specification; chemistry limits are not the same document as B574

Weld filler

AWS A5.14 ERNiCrMo-4 (wire); A5.11 ENiCrMo-4 (electrode)

Buildup and repair

Weld metal corrodes faster than wrought metal in some acids

 

Sources: Haynes International HASTELLOY C-276 datasheet H-2002 (Japanese edition, 2023; haynesintl.com/wp-content/uploads/2024/10/c-276j-1.pdf); ASTM B574-17 abstract; API 600 trim chart (secondary reproductions on Scribd). Haynes values are typical test results, not guaranteed minimums.

 

A note on weld metal. Haynes tested all-weld-metal samples against base metal. In 70% sulfuric acid at 66 °C, weld metal corroded at 5.1 mpy against 2 mpy for wrought base metal. Any overlay or buildup on a trim part should be treated as a different material from the bar it sits on.

 

Make sure it is not a look-alike alloy

 

C276 is often confused with other Hastelloy grades. JN Alloys' published limits show how a PMI (positive material identification) check can separate them. Chromium does most of the work for C22, C2000 and G30. C-4 overlaps C276 on chromium and molybdenum, so ask for tungsten and titanium to be reported too.

 

Table 3. Composition limits that help separate C276 from look-alikes (weight %)

 

Grade (UNS)

Cr

Mo

Fe

PMI note

C276 (N10276)

14.5 – 16.5

15.0 – 17.0

4.0 – 7.0

Tungsten about 3.0 – 4.5 per other published sheets

C22 (N06022)

20.0 – 22.5

12.5 – 14.5

3.0 – 6.0

Chromium separates it clearly

C4 (N06455)

14.0 – 18.0

14.0 – 17.0

3.0 max

Overlaps C276; check tungsten and Ti (0.7 max)

C2000 (N06200)

22.0 – 24.0

15.0 – 17.0

3.0 max

Chromium separates it clearly

G30 (N06030)

28.0 – 31.5

4.0 – 6.0

13.0 – 17.0

Chromium and molybdenum both separate it

 

Source: JN Alloys Hastelloy page, chemical composition table (jnalloys.com/alloys/hastelloy-steel). Tungsten range from Nippon Steel SMC276 data sheet. Confirm detection limits with your PMI instrument or lab.

 

What hardness should replacement C276 trim have?

 

Match the original part's condition, not a single hardness number. Solution-annealed C276 is relatively soft, so hardness cannot identify the alloy, and hard seating faces usually come from hardfacing or cold work.

 

What hardness should replacement C276 trim have

 

Haynes reports typical solution-annealed hardness of 88 HRBW for sheet and plate and 86 HRBW for bar, with typical ASTM grain sizes of about 1 to 6. Haynes states plainly that its property values are typical results and not guaranteed maximums or minimums. The ASTM B574 abstract lists tensile, yield, and elongation minimums for N10276 rod but, in the text we reviewed, no hardness limit. If a hardness acceptance range matters, it has to be written into the purchase order.

 

Table 4. Hardness conditions for C276 trim compared

 

Condition

Hardness evidence

Typical trim role

Watch-outs

Solution annealed (mill condition)

Typical 86 – 88 HRBW (Haynes)

Stems, bodies, trim in less demanding service

Soft; two annealed faces rubbing together have no hardness difference

Cold-worked

Rises with cold reduction; no single value (Haynes)

Springs, bellows and seals; cold-worked product for some sour-service parts

May affect stress-corrosion resistance; Haynes advises re-annealing parts with 7%+ outer-fiber elongation

Hardfaced (Co-Cr-A / Stellite 6 type)

About 38 – 45 HRC typical; API trim chart shows 350 HB minimum on Co-Cr-A seating faces

Seat and disc faces, stems

Hardness depends on dilution from the base metal; verify on the finished deposit

 

Sources: Haynes International C-276 datasheet; API 600 trim chart (secondary); Industrial Monitor Direct valve-trim notes on Stellite 6 hardness (secondary). Cold-worked N10276 was classed as material 4e in the 2003 ISO 15156-3 edition per a Nippon Steel data sheet; read the current edition for sour service.

 

Why hardness difference matters

 

Metal-to-metal seating surfaces that are equally soft tend to tear and stick, which is called galling. Valve designers often avoid it by making one face harder than the other. In the API 600 trim chart, some trim numbers require seating surfaces of at least 250 HB with at least a 50 HB difference between the body and disc faces. The same chart warns that API 600 is written for steel bolted-bonnet gate valves and should not be applied literally to globe and check valves.

 

For C276, this has a practical meaning. The chart lists both a plain C276 trim (19b) and a trim with hardfaced C276 seating surfaces (20b). If the original valve used a hardfaced face and the replacement part is plain annealed C276, the pairing has changed even though the alloy label is the same.

 

Measure hardness the right way

 

  • Use the scale that suits the material. Annealed C276 is read on a Rockwell B scale; hardfaced deposits on a C scale or by Brinell, as the chart or drawing requires.
  • Record where the reading was taken. Heavy machining and blasting work-harden the surface (Haynes), so a finished-surface reading can sit above the bulk value.
  • Do not convert between very different materials. A hardfaced overlay is not the same material as wrought bar, so converting its reading to the annealed scale tells you nothing.

 

Is Stellite hardfacing automatically compatible with C276 service?

 

No. The hardfacing must resist the process fluid as well as the C276 body does, and the way it is applied changes its corrosion behavior. Test the combination before assuming it is safe.

 

The API 600 trim chart states that trim materials, including hardfacing, should have corrosion resistance and temperature limits at least equal to the valve body. Stellite 6 is the most widely used valve hardfacing and is known for galling and corrosion resistance. Even so, a 2020 laboratory study found that cast Stellite 6 resisted corrosion better than laser-clad Stellite 6, because it kept its oxide film better. Another study of cobalt-chromium (Stellite 6B) and nickel (G30) hard alloys noted that they remain challenged in many acidic environments.

 

Table 5. Seating-face options for C276 valve trim compared

 

Option

Strength

Limit to check

Evidence level

Plain annealed C276

Matches body corrosion resistance exactly

Soft; galling and wear risk at metal seats

Haynes (primary)

Cobalt-chromium overlay (Stellite 6 type)

Excellent galling and wear resistance; common choice

Corrosion depends on acid, deposition process and dilution; cast and laser-clad differ

Journal study; valve trade articles (secondary)

Nickel-based overlay (Colmonoy or alloy 625 type)

Often chosen where corrosion or sour service governs

Lower hardness retention than cobalt alloys above about 400 °C per one source

Trade sources only (secondary)

 

Sources: API 600 trim chart (secondary); Ding et al., Protection of Metals and Physical Chemistry of Surfaces, 2020; Valve Magazine, "Hardfacing for Valves"; preprints.org study of Stellite 6B and Hastelloy G30; Industrial Monitor Direct Stellite vs nickel overlay note. Where a source is secondary, confirm with the overlay supplier's data for your fluid.

 

Honest caveat. Stellite is not "bad" for C276 valves. It is used because it solves galling. The point is that it is a different material with its own corrosion limits, so it needs its own approval for the fluid, temperature, and process used to apply it.

 

What surface condition should C276 trim have?

 

Clean, scale-free, and free of embedded iron, with the seat finish and flatness the valve maker specifies. Treat cleanliness and seat geometry as two separate requirements.

 

What surface condition should C276 trim have

 

C276 resists pitting very well. In ASTM G48 testing in 6% ferric chloride, Haynes reports a critical pitting temperature above 150 °C, compared with 15 °C for 316L, 60 °C for 254SMO, and 100 °C for alloy 625. That means the alloy is rarely the weak link. A contaminated surface is. Iron smeared into the surface by steel tooling, wire brushes, or blasting grit can corrode and start pits in the metal beneath it.

 

Table 6. Surface-condition checklist for C276 trim

 

Item

What to check

Method or note

Evidence level

Scale and oxide

Heat-treatment scale removed

Haynes: molten caustic bath then hot acid pickle is most effective; the alloys are generally inert to cold acid pickling

Primary (Haynes)

Blasting residue

No embedded iron or reused grit

Haynes: do not re-use sand, especially if iron-contaminated; pickle after blasting; blasting can work-harden the surface

Primary (Haynes)

Embedded iron

Free-iron test passed

Ferroxyl test or a salt-water soak are used in practice

Practitioner Q&A (informal)

Cleaning route

Pickling or passivation procedure named

ASTM A380 and A967 cover stainless steel; ASTM B614 is cited for nickel alloys; ask for the written procedure

Vendor and trade sources (secondary)

Seat finish and flatness

Per valve maker's drawing

Confirm by seat leakage test (for example API 598), not by assumption

Drawing and test report

 

Sources: Haynes International, descaling and pickling guidance (haynesintl.com); Haynes C-276 datasheet (G48 table); finishing.com practitioner Q&A on Hastelloy cleaning; Harrison Electropolishing passivation pages; Super Stainless Alloys supplier notes. Informal and vendor sources are marked and should not replace the specified procedure.

 

Pickle or passivate? Sources differ. Haynes describes pickling for its nickel alloys. Finishing shops also passivate nickel alloys to A967 or A380. A practitioner thread warns that nitric acid passivation can remove nickel as well as iron on high-nickel alloys. The safe approach is to ask the cleaner for the written procedure and confirm that the valve maker accepts it.

 

Heat treatment needs a clean surface too. One practitioner answer, referring to Haynes' fabrication guidance, notes that nickel alloys should be cleaned of zinc, lead, tin, sulfur, and similar contaminants before any heat treatment or high-temperature use. Treat this as informal advice and check it against the producer's current fabrication guide.

 

How should you verify a replacement trim part on receipt?

 

Check four things before the part goes into the valve: certificate, PMI, hardness (and overlay) report, and cleanliness. Seat leakage testing then confirms the finished assembly.

 

Many trim rejections happen because one document was missing, not because the part was bad. A short receiving checklist prevents this. The overlay items below are adapted from published guidance on accepting hardfaced trim.

 

Table 7. Receiving-inspection checklist for C276 trim

 

Check

What it proves

Acceptance cue

EN 10204 3.1 (or 3.2) certificate

Specification, heat number, delivery condition

Names B574, B564 or CW2M; shows solution-annealed condition

PMI report

Alloy identity

Cr, Mo and tungsten consistent with N10276 (Table 3)

Hardness report

Condition and pairing

Scale, location and values match the drawing or PO

Overlay report (if hardfaced)

Deposit quality

Chemistry, hardness, thickness, no substrate dilution beyond limits, no linear indications on PT or MT

Cleanliness record

No scale or embedded iron

Named cleaning procedure; free-iron test result

Seat leakage test of finished valve

Seating performance

No leakage in the specified hold time (for example API 598)

Sources: Industrial Monitor Direct "API 600 Trim 5 vs Trim 8" acceptance checklist (secondary); EETA summary. Always follow the purchase order and the valve maker's inspection plan.

 

What should you specify for common replacement situations?

 

Start from the original valve: its drawing, trim number and datasheet decide what "matching" means. When the original is unknown, get that information from the valve maker before ordering.

 

Table 8. Replacement decision guide

Situation

What to specify

Why

Original trim was plain annealed C276 and has not galled

Same form and condition; PMI; cleaned and pickled surface

Keeps the original design pairing

Original seating faces were hardfaced

Like-for-like overlay with chemistry, hardness and thickness reports

Changing the overlay changes both wear and corrosion behavior

Seats have a galling history

Ask the valve maker or engineer about hardfacing one face, with an agreed hardness difference

Two soft C276 faces can tear together; the fix is a design decision

Original trim is unknown

Obtain the valve drawing, serial number and trim code from the valve maker

API trim numbers are shorthand and can be applied loosely, especially on globe and check valves

Sour (H2S) service

State the ISO 15156-3 edition, the required condition and the hardness limit

Limits depend on alloy, condition and environment

 

What should a buyer write into the purchase order?

 

Write down the alloy and form, the condition, the hardness requirement with its scale and location, any hardfacing, the cleaning procedure, and the documents to be supplied. Ambiguity in any one of these causes most trim disputes.

 

  • Alloy and form: UNS N10276; B574 bar, B564 forging, or CW2M casting.
  • Condition: solution annealed, cold-worked, or hardfaced, with the overlay specification.
  • Hardness: required range, scale, and where it is measured; any seat-to-disc difference.
  • Surface: cleaning route (for example pickled), free-iron test, seat finish per drawing.
  • Sour service: ISO 15156-3 edition and condition limits, if applicable.
  • Documents: EN 10204 3.1 certificate, PMI report, hardness and overlay reports, cleaning record.

 

JN Alloys supplies Hastelloy C276 and lists nickel alloy machined parts and oil and gas alloy components among its product categories. It also offers processing to customer drawings and publishes a testing equipment list that includes a spectrum analyzer, universal tensile tester, metallographic analyzer, impact tester, and PMI testing. Buyers can request trim parts to their drawing and write the documents above directly into an RFQ. Scope should be confirmed for each part.

 

Frequently Asked Questions

 

Q: Is C276 valve trim hardened by heat treatment?

A: No. Supplier data sheets state that C276 is hardened only by cold work, not by heat treatment, and Haynes International notes that it work-hardens more readily than most austenitic stainless steels. Annealed C276 is therefore relatively soft, and trim designs that need a hard seating face use hardfacing or cold work instead.

 

Q: What is the typical hardness of annealed C276?

A: Haynes reports typical solution-annealed hardness of 88 HRBW for sheet and plate and 86 HRBW for bar. These are typical test results, not guaranteed minimums or maximums, so they should not be used as an acceptance limit unless the purchase order says so.

 

Q: Can Hastelloy C22 or C4 replace C276 trim without approval?

A: No. They are different alloys with different chromium and molybdenum ranges. C22 runs about 20 to 22.5% chromium against 14.5 to 16.5% for C276, so a PMI check separates them easily. Any alloy change needs written engineering approval from the valve owner.

 

Q: Does a 50 HB hardness difference always have to exist between seat and disc?

A: No. A 50 HB minimum difference appears as a note for certain trims in the API 600 trim chart, which is written for steel bolted-bonnet gate valves. The same chart notes it should not be applied literally to globe and check valves. Follow the valve maker's drawing and the purchase order.

 

Q: Is Stellite hardfacing always compatible with C276 service?

A: No. Hardfacing must have corrosion resistance at least equal to the valve body. Published laboratory work shows cobalt-chromium hard alloys can still be challenged in some acids, and that cast and laser-clad Stellite 6 differ in corrosion behavior. Test the combination in the real fluid.

 

Q: Should C276 trim be pickled or passivated?

A: Haynes describes hot acid pickling, often after a molten-salt descaling bath, as the effective cleaning route for its nickel alloys. Some finishing shops also passivate nickel alloys to ASTM A967 or A380. Practitioners warn that the nitric acid recipe used for 316L may not suit nickel alloys, so ask for the written procedure.

 

Q: Does C276 need to be re-annealed after machining?

A: Haynes calls for re-annealing after hot forming, and after cold forming that causes 7% or more outer-fiber elongation. Ordinary machining is not a forming operation, but heavy cutting or blasting can work-harden the surface. Ask the valve maker which rule applies to the part.

 

Q: What standard covers C276 bar for trim?

A: ASTM B574 (ASME SB574) covers rod and bar. For solution-annealed N10276 it requires at least 100 ksi (690 MPa) tensile strength, 41 ksi (283 MPa) yield strength, and 40% elongation. Forgings fall under ASTM B564.

Send Inquiry
Come To Us
And Start Your RFQs Now.
contact us