A purchase order for UNS S32205 pipe, paired with a mill certificate that says S31803, is a paperwork warning, not an automatic rejection. S32205 is a tighter version of S31803, so pipe that truly meets S32205 also meets S31803. The reverse is not guaranteed.

Read the actual heat chemistry on the certificate. If chromium is at least 22.0%, molybdenum at least 3.0%, nitrogen at least 0.14%, and tensile strength is at least 95 ksi (655 MPa), ask the mill to reissue the certificate as S32205 or as dual S31803/S32205. If any value falls short, the pipe does not conform to the order. Reject it, or approve it only through a written engineering concession.
Key terms in plain language
- UNS number: a code (such as S32205) that names one exact alloy chemistry range.
- Duplex 2205: a steel with a two-phase structure, about half ferrite and half austenite. It is strong and resists chloride pitting.
- MTR (mill test report / certificate): the paper that records one production batch (heat) chemistry and test results.
- PMI (positive material identification): a quick on-site test that checks which elements are in the metal.
- PREN: a score for pitting resistance, calculated as %Cr + 3.3 x %Mo + 16 x %N. Higher is better.
Are S31803 and S32205 the Same Duplex Stainless Steel?
They are the same 2205 duplex family but not the same specification. S32205 is a narrower, stricter chemistry window inside the older S31803 range.
S31803 was the original UNS number for 2205 duplex. When argon-oxygen decarburization (AOD) steelmaking let mills control nitrogen on purpose, producers began aiming at the top of the S31803 range. UNS S32205 was created to identify that top-of-range material. Think of two recipes: S31803 allows 2.5 to 3.5 spoons of molybdenum, while S32205 insists on at least 3.0. Every S32205 pipe can be certified as S31803, but a pipe made at the bottom of the S31803 range cannot be certified as S32205.
|
Element (wt. %) |
S31803 |
S32205 |
Why it matters |
|
Chromium (Cr) |
21.0–23.0 |
22.0–23.0 |
Builds the protective surface film |
|
Molybdenum (Mo) |
2.5–3.5 |
3.0–3.5 |
Resists pitting and crevice attack in chlorides |
|
Nitrogen (N) |
0.08–0.20 |
0.14–0.20 |
Adds strength, balances the structure, helps welded areas resist pitting |
|
Nickel (Ni) |
4.5–6.5 |
4.5–6.5 |
Same in both |
|
Carbon (C) |
0.030 max |
0.030 max |
Same in both |
|
Mn / Si / P / S |
2.00 / 1.00 / 0.030 / 0.020 max |
2.00 / 1.00 / 0.030 / 0.020 max |
Same in both |
Source: UNS limits per ASTM A790/A240 as reproduced by SAKY Steel and NeoNickel; history per Langley Alloys. Confirm against the current edition of the standard.
The two grades share the same solution-anneal requirement. ASTM A790 lists 1870–2010°F (1020–1100°C) followed by rapid cooling for both S31803 and S32205. So the difference between them is chemistry and the strength minimum that follows from it, not the heat-treatment route.
Why Does a Mismatch Between the Order and the Certificate Matter?
The grade name fixes three things the buyer relies on: corrosion margin, minimum strength, and the design-code values behind the wall thickness. A certificate naming the wider grade cannot guarantee the S32205 extras until the printed numbers prove them.
Each of the three points below can change a piping design or a contract, even when the two grades look almost identical on a data sheet.
1. Corrosion margin
Chromium, molybdenum and nitrogen set pitting resistance. Using the PREN formula, the lowest chemistry allowed by S31803 scores about 30.5, while the lowest allowed by S32205 scores about 34.1. At the top of the range both score about 37.8. The practical lesson: the grades differ at the floor, and the floor is what a buyer is protected by when no one checks the actual heat.
2. Strength minimums
In current ASTM A790 and A240 tables, S32205 requires 95 ksi (655 MPa) minimum tensile strength, and S31803 requires 90 ksi (620 MPa). Both list 65 ksi (450 MPa) minimum yield. Check the edition on your certificate: a 2001 edition of ASTM A789 lists a 70 ksi (485 MPa) yield minimum for S32205, and some distributor tables still repeat that figure.
3. Design-code values and contract compliance
ASME code tables list S31803 and S32205 as separate entries, and allowable stress follows the tensile minimum. Rolled Alloys publishes 25.7 ksi for 2205 (S31803 basis) at 200°F in one Section VIII-1 data book and 27.1 ksi for 2205 plate in a later data sheet. Our own arithmetic gives the same pattern: 90 ÷ 3.5 = 25.7 and 95 ÷ 3.5 = 27.1. If a designer used the S32205 value and the pipe is really S31803-only, the wall could be thinner than the code allows. Ask the responsible engineer to check the current code edition for your product form.
|
Property |
S31803 |
S32205 |
Note |
|
PREN at lowest allowed chemistry |
30.5 |
34.1 |
EETA calculation from the limits in Table 1 |
|
PREN at highest allowed chemistry |
37.8 |
37.8 |
Top of both ranges is identical |
|
Tensile strength, minimum |
90 ksi (620 MPa) |
95 ksi (655 MPa) |
Current A790 / A240 tables |
|
Yield strength, minimum |
65 ksi (450 MPa) |
65 ksi (450 MPa) |
Older A789 editions differ for S32205 |
|
Elongation, minimum |
25% |
25% |
Same in both |
|
Hardness, maximum (pipe) |
290 HBW / 30 HRC |
290 HBW / 30 HRC |
A240 plate allows 293 HBW / 31 HRC |
|
Solution anneal |
1870–2010°F |
1870–2010°F |
ASTM A790, rapid cooling |
Sources: ASTM A790-08a; ASTM A240 values per ATI and Rolled Alloys data sheets; ASTM A789-01 sample; ASTM A1082 table as reproduced by Torqbolt. PREN is a ranking index, not a guarantee of field performance.
What Should You Check on the Certificate Before Anything Else?
Ignore the grade name in the header. Compare the printed heat values against the S32205 limits, line by line.
A certificate that says S31803 may still describe steel that meets S32205, because mills often certify to the wider grade. Only the numbers can show which case you have.
|
Check |
S32205 limit to meet |
If it fails |
|
Chromium |
22.0–23.0% |
Below 22.0% means S31803-only steel |
|
Molybdenum |
3.0–3.5% |
Below 3.0% means S31803-only steel |
|
Nitrogen |
0.14–0.20% |
Below 0.14%, or not reported, means S32205 is unproven |
|
Nickel and carbon |
Ni 4.5–6.5%, C 0.030% max |
Outside range: not 2205 duplex to either spec |
|
Tensile strength |
95 ksi (655 MPa) min |
Lower value can still pass S31803 at 90 ksi |
|
Yield and elongation |
65 ksi (450 MPa) and 25% min |
Failure means non-conforming to both grades |
|
Hardness |
290 HBW / 30 HRC max (pipe) |
Over limit: review heat treatment and test method |
|
Heat treatment |
Solution anneal 1870–2010°F, rapid cool |
Missing record: request confirmation from the mill |
Sources: ASTM A790/A240 limits as listed in Table 1 and Table 2. Verify against the standard edition named on your purchase order.
Then check the paper trail. These five items catch most certificate problems:
- The heat number on the certificate matches the number stamped or marked on the pipe.
- The certificate names the product standard, its edition, and the product form (seamless or welded).
- The document type is EN 10204 3.1 or better. A 3.1 certificate is issued by the manufacturer and validated by an authorized inspection representative independent of the manufacturing department.
- Nitrogen is reported as a measured value, not left blank.
- Values near a limit, such as nitrogen at 0.14%, get a second look, because small measurement differences can turn a pass into a fail.
Can a Handheld PMI Gun Confirm S32205?
Not by itself. Handheld XRF reads chromium, nickel and molybdenum, but it cannot measure nitrogen, and nitrogen is one of the three elements that separate S32205 from S31803.
Nitrogen is a very light element that handheld X-ray analyzers cannot see. Industry sources also state that handheld LIBS cannot test for nitrogen. Portable spark OES and laboratory methods can. Rolled Alloys notes that combustion techniques give the most accurate nitrogen results. PMI is still valuable: it can quickly expose a wrong alloy such as 316L, and a molybdenum reading near 2.6% on pipe sold as S32205 is a strong red flag.
|
Method |
Cr, Ni, Mo |
Nitrogen |
Best use at receiving |
|
Handheld XRF |
Yes |
No |
Fast screening of every pipe for wrong-alloy mix-ups |
|
Handheld LIBS |
Limited |
No |
Not suitable for separating S31803 from S32205 |
|
Portable spark OES |
Yes |
Yes |
On-site check of nitrogen when a lab is not nearby |
|
Laboratory analysis (OES / combustion) |
Yes |
Yes, most accurate |
Settling disputes and borderline nitrogen values |
Sources: Valve Magazine (2013) on PMI limits; Hitachi High-Tech PMI technical notes; Rolled Alloys PMI article. Readings near a limit should be confirmed by laboratory analysis.
How Do You Resolve the Mismatch Step by Step?
Hold the pipe, test it against the S32205 limits, then choose one of three outcomes: correct the certificate, reject the pipe, or approve a documented deviation. Never accept a verbal assurance.
A clear sequence keeps the decision based on evidence and leaves a record that survives an audit.
- Quarantine and tag. Keep the pipe out of fabrication until the question is closed.
- Compare. Check the heat chemistry and mechanical results against Table 3.
- Verify identity. Match heat numbers, run PMI for Cr, Ni and Mo, and send a sample to a laboratory for nitrogen if it is missing or borderline.
- Decide. Use Table 5 to pick the outcome.
- Document. File the corrected certificate, any nonconformance report, and any purchase order amendment together.
|
What the data shows |
What it means |
Action |
|
Every value meets S32205; certificate only names S31803 |
Under-certification or paperwork error |
Ask the manufacturer to reissue the certificate as S32205 or dual S31803/S32205 |
|
Cr, Mo or N is below S32205 but inside S31803 |
Valid S31803 pipe, but not what was ordered |
Reject and replace, or obtain a written engineering concession, amend the PO, and re-check the design basis |
|
Values missing, unreadable, or contradicted by PMI |
Traceability gap |
Hold, run independent laboratory tests, release only after the gap is closed |
|
Chemistry outside both ranges |
Not 2205 duplex to either specification |
Reject |
Sources: S32205 dual-certification principle per Langley Alloys; certificate responsibilities per EN 10204:2004 summaries. Corrected certificates must come from the manufacturer, not be retyped by a trader.
One practical point: because S32205 chemistry satisfies S31803, a mill can issue a dual certificate naming both. If your project may later accept either grade, ask for the dual wording so the paperwork matches the steel.
How Can Buyers Prevent This Mismatch on the Next Order?
Write the purchase order so the certificate must prove S32205, not merely name it.
Most mismatches begin with loose wording. The names "2205" and "1.4462" cover both S31803 and S32205, so neither name settles which chemistry the buyer expects.

State the full designation: UNS S32205, product standard (for example ASTM A790/A790M), seamless or welded, and the edition.
Say whether dual certification is acceptable. A suggested wording: S31803-only certification is not accepted unless the actual heat chemistry meets S32205.
Require heat analysis including nitrogen, with actual mechanical test values, on an EN 10204 3.1 certificate (or 3.2 if a third party must co-sign).
Define receiving inspection: heat-number match, PMI for Cr, Ni and Mo on every length, and a nitrogen check by OES or laboratory on each heat.
Agree in advance how discrepancies are handled, including who reissues the certificate and how long shipment is held.
The same logic applies to every product form in a duplex 2205 order:
|
Product form |
Common ASTM spec |
S31803 designation |
S32205 designation |
|
Pipe |
A790 |
UNS S31803 |
UNS S32205 |
|
Tube |
A789 |
UNS S31803 |
UNS S32205 |
|
Plate and sheet |
A240 |
UNS S31803 |
UNS S32205 |
|
Forged flanges and fittings |
A182 |
Grade F51 |
Grade F60 |
Sources: Langley Alloys (F51 and F60 naming); Rolled Alloys 2205 data sheet (specification list). Bar specifications such as A276 and A479 follow the same two-designation pattern.
Frequently Asked Questions
Q: Is S32205 better than S31803?
A: S32205 guarantees a higher floor for chromium, molybdenum and nitrogen, so its minimum pitting resistance is higher. Many producers make one 2205 product that meets both. Neither grade is better at the top of the range.
Q: Can S32205 pipe be certified as S31803?
A: Yes. Steel that meets S32205 also meets S31803, so it can carry a dual certificate. The reverse is not true.
Q: Can we accept S31803-only pipe on an S32205 order?
A: Not automatically. It requires written approval from the responsible engineer, a purchase order amendment, and a check that corrosion margin and code stress values still work.
Q: Does a PMI gun tell S32205 from S31803?
A: No. Handheld XRF cannot measure nitrogen. It can flag low chromium or molybdenum, but nitrogen needs spark OES or laboratory analysis.
Q: Do the heat-treatment requirements differ?
A: No. ASTM A790 lists the same 1870–2010°F (1020–1100°C) solution anneal with rapid cooling for both grades.
Q: Does naming the steel "2205" or "1.4462" solve the problem?
A: No. Both names cover S31803 and S32205. The UNS number is what separates them, so put it on the purchase order.

