Sigma Phase Embrittlement in Duplex Stainless Steel: Time-Temperature-Precipitation Curves

Jul 23, 2026

Leave a message

John Zhang
John Zhang
Experienced Technical Director at Jinie Technology, specializing in stainless steel and nickel alloy solutions. Passionate about material science and process optimization. Over 10 years of expertise in custom metal processing and technical consultation.

Sigma phase forms in duplex stainless steel fastest between roughly 700°C and 900°C, with the nose of the time-temperature-precipitation (TTP) curve typically located around 800–850°C - meaning that narrow band, not higher or lower temperatures, is where the fastest, most damaging precipitation occurs. A sigma fraction as small as 1–3% by volume can cause a severe, disproportionate drop in impact toughness and pitting corrosion resistance, which is why controlling time spent in this range during welding and heat treatment is a strict fabrication requirement, not a minor process detail.

 

Sigma Phase Embrittlement in Duplex Stainless Steel

 

Duplex stainless steel earns its reputation - high strength, excellent chloride resistance - from a balanced microstructure of roughly equal parts austenite and ferrite. That balance is fragile at elevated temperature. Held too long in the wrong temperature window, the ferrite phase partially transforms into an intermetallic compound called sigma phase, and the alloy's most valuable properties collapse. This article explains what sigma phase is, what its time-temperature-precipitation curve looks like, and what fabricators need to do to stay off it.

 

What Is Sigma Phase, and Why Does It Embrittle Duplex Stainless Steel?

 

Sigma phase is a hard, brittle intermetallic compound rich in chromium and molybdenum that forms when the ferrite in duplex stainless steel decomposes at elevated temperature - and because it strips chromium and molybdenum from the surrounding matrix, it damages both toughness and corrosion resistance at the same time.

 

Sigma phase forms through a eutectoid-type reaction in which ferrite decomposes into sigma phase plus secondary austenite. It nucleates preferentially at ferrite-austenite phase boundaries and ferrite-ferrite grain boundaries - often preceded by a related intermetallic, chi phase, which forms first at ferrite-ferrite boundaries and is later consumed as sigma phase grows.

 

Because sigma phase is intrinsically hard and brittle, and because its formation pulls chromium and molybdenum out of the surrounding matrix, it creates two problems simultaneously: a physically brittle secondary phase sitting at grain boundaries, and chromium/molybdenum-depleted regions next to it that are far more vulnerable to localized corrosion. This dual damage mechanism is why sigma phase embrittlement is treated as a critical fabrication risk rather than a cosmetic metallurgical curiosity.

 

What Does a Time-Temperature-Precipitation (TTP) Curve Show for Sigma Phase?

 

A TTP curve plots the temperature an alloy is held at against how long it takes for a given amount of sigma phase to appear, producing a characteristic C-shaped curve whose 'nose' marks the fastest possible precipitation - for duplex stainless steel, that nose typically sits around 800–850°C.

 

What Does a Time-Temperature-Precipitation TTP Curve Show for Sigma Phase

 

Researchers build these curves by holding solution-annealed samples at a series of fixed temperatures, then measuring how much sigma phase has formed after different holding times, from minutes to over a thousand hours. Plotted on a time (log scale) versus temperature axis, the resulting curve resembles a sideways "C": precipitation is slow at both the high and low ends of the risk range, and fastest in the middle.

 

Studies on wrought UNS S31803 (2205) duplex stainless steel have identified peak sigma-formation kinetics around 850°C, with published TTP work spanning holding times up to and beyond 1,000 hours to fully characterize the curve. Independent work on cast duplex grades, super duplex grades, and lean duplex compositions consistently places the nose of the curve in the same general 800–850°C band, even though the exact shape and timing shift somewhat with alloy composition.

 

What Temperature Range Is Most Dangerous for Sigma Phase Formation?

 

The practical danger zone spans roughly 700°C to 950°C across duplex and super duplex grades, with the single most dangerous temperature - the fastest precipitation - consistently reported around 800–850°C.

 

Alloy / Study Basis

Reported Precipitation Range

Reported Fastest (Nose) Temperature

2205 (UNS S31803), wrought

700–900°C

~850°C

CD3MN, cast duplex

700–900°C

~800°C (nose at ~100 min)

2507 super duplex

750–950°C

~850°C (up to ~18% area fraction)

General stainless steel families (review data)

Broad, alloy-dependent

800–850°C

 

Outside this band, the picture changes: below roughly 700°C, diffusion is slow enough that sigma formation becomes very sluggish, though prolonged exposure can still allow it, and a separate, lower-temperature embrittlement mechanism - 475°C embrittlement from spinodal decomposition of the ferrite - becomes the more relevant risk instead. Above roughly 950–1000°C, sigma phase becomes thermodynamically less stable and tends to dissolve back into the matrix, which is the basis for solution annealing as a corrective heat treatment.

 

How Little Sigma Phase Does It Take to Cause a Problem?

 

A remarkably small amount - commonly cited as low as 1% to 3% by volume - is enough to cause a considerable, disproportionate drop in impact toughness, which is what makes sigma phase control unusually strict compared with many other metallurgical defects.

 

This is the detail that most surprises engineers new to duplex stainless steel: sigma phase does not need to accumulate to a large fraction before it becomes dangerous. Multiple independent studies on 2205 duplex stainless steel report that sigma contents in the low single digits by volume are already sufficient to cause a marked toughness collapse, and that impact energy curves track closely with the shape of the sigma precipitation curve itself - the same 800–850°C range that precipitates sigma fastest is also the range that produces the lowest impact toughness after aging. As holding time and sigma content increase further, toughness continues to degrade, but the steepest, most consequential drop happens early, at fractions a casual visual inspection could easily miss.

 

Does Sigma Phase Also Hurt Corrosion Resistance, or Just Toughness?

 

Both. Sigma phase precipitation measurably lowers pitting potential and raises susceptibility to intergranular and pitting corrosion, because the chromium- and molybdenum-depletion around each sigma particle undermines the passive film exactly where it's needed most.

 

Does Sigma Phase Also Hurt Corrosion Resistance or Just Toughness

 

The corrosion consequence follows directly from how sigma phase forms: as chromium and molybdenum diffuse into the growing sigma particle, the immediately surrounding matrix becomes locally depleted in the very elements that stabilize the passive oxide film. Electrochemical testing on aged duplex stainless steel shows pitting potential dropping as sigma content rises, with the passive region narrowing and eventually becoming unstable at higher sigma fractions.

 

Pits have been shown to nucleate preferentially in these chromium-depleted zones surrounding sigma particles, and the severity scales with both the amount and distribution of sigma present - coarse, concentrated sigma particles are typically more damaging than the same volume fraction finely dispersed. In short, a component can fail a corrosion test in exactly the same welded or heat-affected region where it would also fail an impact test.

 

Why Does Welding Put Duplex Stainless Steel at Risk of Sigma Phase?

 

The heat-affected zone next to a weld inevitably passes through the 700–950°C danger band during both heating and cooling, and multiple weld passes or slow interpass cooling can accumulate enough time in that band to precipitate damaging sigma phase even when no single pass looks obviously overheated.

 

Every arc welding pass creates a temperature gradient radiating out from the weld pool, and somewhere along that gradient, base metal briefly sits within the sigma-formation range. A single fast pass may not linger there long enough to matter. Multi-pass welding, high heat input, inadequate interpass temperature control, or slow cooling in thick sections can each extend the time spent in the danger band well past what the alloy's TTP curve allows before damaging sigma content appears. This is why welding procedures for duplex stainless steel specify maximum heat input, controlled interpass temperature, and - in many cases - a requirement for rapid cooling through the critical range, rather than leaving cooling rate to chance.

 

How Fast Does Sigma Phase Actually Form - Minutes, or Hours?

 

At the nose of the curve, detectable sigma phase can begin forming in well under two hours, and in some cast and highly alloyed compositions, within roughly 100 minutes or less - fast enough that a slow weld cooldown or an improperly controlled post-weld heat treatment is a real, not theoretical, risk.

 

Published TTP data for cast CD3MN duplex stainless steel places the nose of the curve at approximately 800°C with detectable sigma formation beginning around 100 minutes of holding time. Kinetic studies on wrought 2205 report the fastest transformation kinetics at 850°C, with full characterization studies extending holding times out to over 1,000 hours to map the complete curve, including the much slower formation rates at the edges of the danger band. The practical implication is asymmetric: the fastest part of the curve operates on a timescale of roughly an hour to a few hours, which is well within the time a thick-section weldment or an improperly controlled furnace cycle can spend passing through that temperature range.

 

What Cooling Rate Is Required After Solution Annealing to Avoid Sigma Phase?

 

Cooling rates faster than roughly 0.25 K/s through the sigma-formation range are reported to suppress sigma phase formation during continuous cooling from solution-annealing temperature, which is why water quenching or forced-air cooling - not slow, still-air cooling of thick sections - is standard practice for duplex stainless steel.

 

What Cooling Rate Is Required After Solution Annealing to Avoid Sigma Phase

 

Solution annealing at high temperature (typically above roughly 1000–1050°C) dissolves any existing sigma phase and resets the austenite-ferrite balance, but the benefit is only preserved if the subsequent cooldown passes through the sigma-formation range quickly enough to prevent new precipitation. Continuous-cooling-transformation studies built alongside TTP data confirm that sufficiently fast cooling - with published thresholds in the range of roughly a quarter of a degree Celsius per second - avoids meaningful sigma formation even though the same material would readily form sigma if held isothermally in the danger band. This is precisely why thick-section duplex components require aggressive quenching after solution annealing: mass alone can slow the cooling rate at the component's core below this threshold even when the surface cools quickly.

 

How Is Sigma Phase Detected in Finished or In-Service Components?

 

Metallographic examination with selective etching remains the reference method, but nondestructive techniques - including magnetic and electrochemical methods that exploit sigma phase's distinct properties from ferrite - are increasingly used to screen components without cutting samples.

 

Metallography: polished sections with selective etchants reveal sigma phase morphology and distribution directly, and remain the standard for definitive volume-fraction quantification.

 

Impact testing: Charpy testing is a strong indirect indicator, since impact energy curves closely track sigma content in aged duplex stainless steel.

 

Magnetic and electromagnetic methods: because sigma phase is non-magnetic while ferrite is ferromagnetic, its formation measurably changes the material's magnetic response, enabling nondestructive screening approaches.

 

Electrochemical testing: potentiodynamic polarization can detect the drop in pitting potential associated with sigma-related chromium and molybdenum depletion, providing an indirect but sensitive corrosion-based screen.

 

For critical fabricated components, a combination of approaches - rather than any single test - gives the most reliable picture, since toughness loss, corrosion susceptibility, and directly observed sigma content don't always move in lockstep at very low sigma fractions.

 

What Should Fabricators Do to Prevent Sigma Phase Embrittlement?

 

Control heat input and interpass temperature during welding, cool rapidly through the 700–950°C range after any high-temperature exposure, and verify the result with impact testing rather than relying on visual inspection alone.

 

What Should Fabricators Do to Prevent Sigma Phase Embrittlement

 

Specify and enforce maximum interpass temperature and heat input limits in the welding procedure specification, since these directly control how long the heat-affected zone dwells in the danger band.

 

Use rapid cooling - water quenching or forced-air cooling as appropriate to section thickness - after solution annealing or any high-temperature thermal cycle, rather than allowing slow, still-air cooling.

 

Account for section thickness explicitly: thick components cool more slowly at their core and may need more aggressive quenching to achieve the same effective cooling rate as thin sections.

 

Require Charpy impact testing on procedure qualification records and, where practical, on production welds, since toughness loss is one of the most sensitive indicators of incipient sigma formation.

 

Where service conditions involve repeated or prolonged exposure near the danger band, evaluate alloy selection itself - some duplex compositions and alloying strategies delay sigma formation more effectively than others.

 

Frequently Asked Questions

 

At what temperature does sigma phase form fastest in duplex stainless steel?

Most published time-temperature-precipitation studies place the fastest sigma formation - the 'nose' of the curve - around 800–850°C, though the exact value shifts slightly with alloy composition.

 

How much sigma phase is dangerous?

Surprisingly little. Multiple studies report considerable toughness loss from sigma fractions in the range of roughly 1% to 3% by volume, well before the phase becomes easy to spot without metallographic examination.

 

Does sigma phase affect corrosion resistance or just mechanical toughness?

Both. Sigma phase formation depletes chromium and molybdenum from the surrounding matrix, which measurably lowers pitting potential and raises intergranular and pitting corrosion susceptibility, in addition to reducing impact toughness.

 

Can sigma phase be removed once it has formed?

Yes, generally through solution annealing at sufficiently high temperature (commonly above roughly 1000–1050°C) followed by rapid cooling, which dissolves the sigma phase back into the matrix and restores the balanced microstructure - provided the subsequent cooldown is fast enough to prevent reformation.

 

Why is welding the most common cause of sigma phase in the field?

Because the heat-affected zone around any weld inevitably passes through the sigma-formation temperature range during heating and cooling, and multi-pass welding or high heat input can accumulate enough time in that range to precipitate damaging sigma content.

 

Send Inquiry
Come To Us
And Start Your RFQs Now.
contact us