Incoloy 800H characteristics
Incoloy 800H(UNS N08810, 1.4958, 1.4876) has good creep-rupture properties at temperatures above 1100°F (600°C). It remains ductile during long term use at temperatures below 1290°F (700°C) due to a maximum titanium and aluminum content of 0.7%. Alloy 800 with a standard anneal is recommended for service below 1100°F (600°C). Alloy 800H resists reducing, oxidizing and nitriding atmospheres, as well as, atmospheres that alternate between reducing and oxidizing. The alloy remains stable in long term high temperature service.
Alloy 800H has the following properties
1. Excellent corrosion resistance in extremely high temperature aqueous media up to 500°C
2. Good resistance to stress corrosion
3. Good workability
Metallographic structure of Incoloy 800H
800H is a face-centered cubic lattice structure. Very low carbon content and increased Ti:C ratio increase structural stability and maximum resistance to sensitization and intergranular corrosion. A low-temperature annealing around 950°C ensures a fine-grained structure.
Corrosion resistance of Incoloy 800H
800H can resist corrosion of many corrosive media. Its high nickel content makes it resistant to stress corrosion cracking in aqueous corrosion conditions. The high chromium content provides better resistance to pitting and crevice corrosion cracking. The alloy has good corrosion resistance to nitric acid and organic acids, but limited corrosion resistance in sulfuric acid and hydrochloric acid. Good corrosion resistance in oxidizing and non-oxidizing salts, in addition to the potential for pitting corrosion in halides. It also has good corrosion resistance in water, steam and mixtures of steam, air and carbon dioxide.
The Chemical Composition of Incoloy 800H, %
|
Grade |
Ni |
Cr |
Fe≤ |
Al |
C |
Mn |
P≤ |
Si≤ |
S≤ |
Al & Ti |
Cu≤ |
|
Incoloy 800H |
30.0-35.0 |
19.0-23.0 |
39.5 |
0.15-0.60 |
0.05-0.10 |
1.5 |
0.045 |
1.00 |
0.015 |
0.30-1.20 |
0.75 |
Physical Properties of Incoloy 800H
Density: 8.0 g/cm3
Melting point: 1350-1400 ℃
Incoloy 800H Mechanical Properties
|
Mechanical properties |
Tensile, min, ksi[MPa] |
Yield, min, ksi[MPa] |
Elongation, %(min) |
|
Incoloy 800H |
65[450] |
25[170] |
30 |
Incoloy 800H Equivalent Grades
|
STANDARD |
WERKSTOFFNR. |
UNS |
JIS |
BS |
GOST |
AFNOR |
EN |
OR |
|
Incoloy 800H |
1.4958 / 1.4876 |
N08810 |
NCF 800H |
NA 15(H) |
ЭИ670 |
Z8NC33-21 |
X5NiCrAlTi31-20 |
XH32T |
ASTM Specifications
|
Product From |
Rod and Bar |
Plate, Sheet & Strip |
Seamless Pipe & Tube |
Welded fittings |
Forging |
|
Standard |
ASTM B408, EN 10095 |
ASTM A240/ A480/B409/ B906 |
ASTM B829/ B407 |
ASTM B366 |
ASTM B564/DIN 17460 |
Incoloy 800HApplication
- Chemical and Petrochemical Processing-process equipment for theproduction of ethylene, ethylene dichloride, acetic anhydride, ketene,nitric acid and oxy-alcohol.
- Petroleum Refining-steam/hydrocarbon reformers andhydrodealkylation units.
- Power Generation-steam super-heaters and high temperature heatexchangers in gas-cooled nuclear reactors, heat exchangers andpiping systems in coal-fired power plants.
- Thermal Processing Fixtures-radiant tubes, muffles, retorts andfixtures for heat-treating furnaces.
Hot Tags: incoloy 800h / uns n08810 / 1.4958, China incoloy 800h / uns n08810 / 1.4958 manufacturers, suppliers, alloy for chemical industry, alloy for forging, alloy in green technology, alloy in batteries, alloy in waste treatment, alloy in resource conservation
